Chrome plating
A thin layer of chromium over nickel over a base metal. Common on exhaust tips, some wheels, and the bumpers and trim of older cars.
Hard and glossy, but once the plating is chipped or pitted, moisture reaches the metal underneath.
Start by working out what the shiny part actually is. Real chrome plating, polished stainless steel, anodized aluminum and chrome-look plastic all look alike and need different care, and the wrong metal polish strips the finish off the last two.
For every one of them the routine starts the same way: wash with regular car soap, rinse, and dry fully, and keep wheel cleaner and road salt off it. Metal polish, where it is appropriate, comes after that, and a wax or sealant afterwards slows the next round of spotting.
Bright trim is easy to overdo, and the damage is often permanent. The aim here is to keep you from the products that cause it.
Check the owner's manual or ask the dealer if you are unsure. A magnet will not stick to plastic or aluminum, which helps rule things out.
A thin layer of chromium over nickel over a base metal. Common on exhaust tips, some wheels, and the bumpers and trim of older cars.
Hard and glossy, but once the plating is chipped or pitted, moisture reaches the metal underneath.
Solid metal rather than a coating. Common on exhaust tips and some trim strips.
Takes metal polish well, and can show heat tints near the exhaust that are often permanent.
Window surrounds, roof rails and trim on many modern cars. The finish is a thin protective layer on the surface.
Metal polish removes that layer and leaves the bare metal exposed.
Grilles, badges, mirror caps and window trim on many modern cars. A very thin metallic layer on plastic, sometimes under a clear finish.
It scratches and peels if you treat it like metal.
Car shampoo, a clean mitt, light pressure. Most of the film on bright trim is road grime, and soap and water removes it. Keep the wheel towel and brush off it.
Chrome and polished metal show water spots more than paint does. Mineral deposits, and in this city salt from sea air, dry into a haze. A clean microfiber, and a blower for crevices, gets it dry before it spots.
If there is a light haze or fine surface spotting that washing did not shift, use a polish made for chrome or stainless, with a soft microfiber, a small amount and light pressure. Test a hidden area first.
If washing does not fix it, that is a reason to ask someone, not to reach for a stronger polish.
A thin coat gives salt, water and road film something to land on instead of the plating, and makes the next wash easier. Buff off the excess.
After a drive along the coast, or a few foggy days parked near the ocean, a quick rinse takes the salt off before it works into any pits.
When in doubt, stick to soap and water and ask.
| Surface | Car soap and water | Metal polish |
|---|---|---|
| Chrome plating | Yes | Yes, if the plating is intact and the polish is made for chrome |
| Polished stainless steel | Yes | Yes, with a polish made for stainless |
| Anodized or clear-coated aluminum | Yes | No. It strips the finish unless the product says it is safe for it |
| Chrome-look plastic | Yes | No. It scratches and can remove the metallic layer |
If you cannot tell which one you have, treat it as the most delicate: soap, water and a soft cloth.
Chrome does not rust by itself. Rust starts when the plating is chipped or worn through and moisture reaches the metal underneath. Salt air makes that happen faster, which matters in a city where most of the western half sits in a marine layer.
Light surface rust specks on plating that is otherwise sound sometimes polish off. Pitting, where the plating has bubbled or flaked, does not. A polish can slow it down but cannot refill it. Bringing back a badly pitted bumper is a re-plating job done by a specialist metal finisher, not a detailing one.
Blue or gold discoloration on a stainless exhaust tip is heat, not dirt. Soot comes off; a heat tint often only partly does.
Bright trim is washed and dried with the rest of the car in an exterior wash. Chrome polishing and re-plating are not among our listed services, so if you want pitted tips or a classic bumper brought back, ask before you book. For faded black plastic trim, which is a different problem, see the black trim guide.
Send photos with a quote request and we will tell you what we would and would not do.
More short answers live on the FAQ.
The services this guide is about:
Back to the full guide library.
Most of the damage done to bright trim comes from reaching for something stronger than it needed.