Gloss clear-coated carbon
The common case on body panels, roofs and mirror caps. It is a clear layer over the weave, and it is cared for like paint.
Exposed carbon fiber on a car is a woven fabric set in resin and covered by a clear layer, so you care for the clear layer, not the weave. Wash it like paint: a pH-neutral soap, a clean mitt, light pressure, and nothing abrasive.
The real risk is UV. A clear layer left bare for years can haze, yellow or lose its gloss, and wax does not repair that. Protect carbon the way you protect paint, and keep polish, clay and harsh solvents off it unless someone has checked the layer first.
Most carbon problems are clear-coat problems. The care is the same careful care paint gets, with a little extra restraint.
The common case on body panels, roofs and mirror caps. It is a clear layer over the weave, and it is cared for like paint.
Care is mostly what you leave out: no wax, no polish, no rubbing. The matte paint guide applies.
Splitters, diffusers and undertrays are often less finished. They take chips and scuffs, and rinsing and a gentle wash are the whole routine. Scrubbing a cut edge helps nothing.
Dash and console trim. A clean, barely damp microfiber and a dry one after it. Do not soak it, and do not spray product onto the panel.
Soap dries on a hot panel and spots. Carbon on a roof or a bonnet takes the sun, so wait until it is cool.
Take the loose grit off first. Grit dragged across a clear layer is what scratches it.
A pH-neutral soap and a plush mitt, in straight lines. The method is the one in the wash guide.
Cut edges and chipped corners, where the weave shows, are the weak point. Keep close-range pressure and wet cloths off them.
A clean, plush towel, patted or blotted, or a blower. Do not drag it across.
Haze, yellowing and fine swirls show up in direct sun. Early notice means early protection.
Most of these are the clear layer, not the carbon.
| What you see | What it usually is | What to do |
|---|---|---|
| Dull or hazy gloss | Wear or UV damage to the clear layer, or old residue | Wash with a pH-neutral soap first. If it stays hazy, the layer is the problem, and wax will not repair it |
| Yellowing or cloudiness | UV breaking down the clear layer | Protect early. A failed layer is a job for a refinisher, not for polish |
| Fine swirls | Washing marks in the clear layer | Prevention first. Machine correction of a carbon panel is something we would only discuss in a quote, and we may decline |
| Water spots | Minerals left as water dried, sometimes etched | Pat dry. Light spots lift with a damp cloth. See removing water spots |
| Chips or cracks in the weave | Impact damage | Not a detailing job. A coating does not stop chips |
| Fingerprints and dust on interior trim | Skin oil and static | A clean, barely damp microfiber, then a dry one |
We do not repair or refinish carbon. We wash, decontaminate where appropriate and protect it.
Protect gloss clear-coated carbon the way you protect paint, with a sealant or a coating. A coating makes washing easier and resists chemical etching, and it does not stop stone chips. See what can be ceramic coated and ceramic coating.
Matte and satin carbon is different. Use only products made for matte, or nothing, and ask the maker or the person who finished it what is approved. Interior carbon needs no coating, only a light touch.
UV matters even in San Francisco's fog. A bare clear layer on a roof or a bonnet takes the sun, which is the reason protection matters more than polish.
A BMW M3 Competition in the Outer Sunset was booked as paint correction and ceramic coating. The exotic page describes one machine-polishing pass on black paint and Gtechniq EXO v5 over the top, including the carbon roof, and the photos include the carbon-fibre roof before the work.
A BMW M4 in Portola was an exterior detail with 26 photos and 7 matched pairs, one of them the carbon trunk lid, bumper and rear plate. The Ferrari 296 GTS full detail in Pacific Heights covered the cabin, the carbon trim and the seats, as the exotic page describes it.
These are cars with carbon on them, and more BMW work is on the BMW page. We have not done carbon repair or refinishing, and we do not offer it.
If your car has exposed carbon, say which panels, and whether the finish is gloss or matte. The exotic car detailing page lists the high-end jobs we have done and what each was.
More short answers live on the FAQ.
The services this guide is about:
Back to the full guide library.
The weave is not the thing at risk. The clear layer is, and it wants gentle washing, protection from the sun and no abrasives.